(2026) 200-301 Dumps and Practice Test (1800 Questions)
Guide (New 2026) Actual Cisco 200-301 Exam Questions
Cisco 200-301 exam is a challenging certification test that requires a significant amount of preparation. Candidates must have a thorough understanding of networking concepts and protocols to pass the exam. Cisco Certified Network Associate Exam certification is valid for three years, after which candidates must recertify to maintain their CCNA status. The Cisco 200-301 exam is an excellent way for IT professionals to validate their networking skills and advance their career in the field of networking.
NEW QUESTION # 700
Company has decided to require multifactor authentication for all systems. Which set of parameters meets the requirement?
- A. password of 8 to 15 characters and personal 12-digit PIN
- B. personal 10-digit PIN and RSA certificate
- C. complex password and personal 10-digit PIN
- D. fingerprint scanning and facial recognition
Answer: B
NEW QUESTION # 701
Refer to the exhibit. Which command provides this output?
- A. show ip route
- B. show ip interface
- C. show interface
- D. show cdp neighbor
Answer: D
NEW QUESTION # 702
Refer to the exhibit.
After configuring a new static route on the CPE. the engineer entered this series of commands to verify that the new configuration is operating normally When is the static default route installed into the routing table?
- A. when 203 0 113.1 is no longer reachable as a next hop
- B. when a route to 203.0 113 1 is learned via BGP
- C. when the default route over external BGP changes its next hop
- D. when the default route learned over external BGP becomes invalid
Answer: A
NEW QUESTION # 703
Drag and drop the IPv6 address type characteristics from the left to the right.
Answer:
Explanation:
Explanation:
NEW QUESTION # 704
Which SDN plane forwards user-generated traffic?
- A. Policy plane
- B. Management plane
- C. Data plane
- D. Control plane
Answer: C
NEW QUESTION # 705
What is a function of Wireless LAN Controller?
- A. monitor activity on wireless and wired LANs
- B. use SSIDs to distinguish between wireless clients.
- C. send LWAPP packets to access points.
- D. register with a single access point that controls traffic between wired and wireless endpoints.
Answer: C
Explanation:
Explanation
Lightweight APs (LAPs) is devices require no initial configuration. LAPs use the Lightweight Access Point Protocol (LWAPP) to communicate with a WLAN controller (WLC), as shown in the below figure.
Controller-based APs are useful in situations where many APs are required in the network. As more APs are added, each AP is automatically configured and managed by the WLC.
NEW QUESTION # 706
Drag and drop the Cisco Wireless LAN Controller security settings from the left onto the correct security mechanism categories on the right.
Answer:
Explanation:
NEW QUESTION # 707
Refer to the exhibit. After the configuration is applied, the two routers fail to establish an OSPF neighbor relationship. what is the reason for the problem?
- A. Router2 is using the default hello timer.
- B. The network statement on Router1 is misconfigured.
- C. The OSPF router IDs are mismatched.
- D. The OSPF process IDs are mismatched.
Answer: A
NEW QUESTION # 708
Drag and drop the Cisco Wireless LAN Controller security settings from the left onto the correct security mechanism categories on the right.
Answer:
Explanation:
NEW QUESTION # 709
Refer to the exhibit. The link between PC1 and the switch is up, but it is performing poorly.
Which interface condition is causing the performance problem?
- A. There is an interface type mismatch
- B. There is a duplex mismatch on the interface
- C. There is a speed mismatch on the interface.
- D. There is an issue with the fiber on the switch interface.
Answer: B
Explanation:
The PC's port runs in full duplex, while the Fa0/1 port on the switch is in auto-negotiate mode.
This results in a duplex mismatch that causes the switchport to operate as half-duplex, which culminates in poor performance on the link.
"A duplex mismatch occurs when two connected devices are configured in different duplex modes.
This may happen, for example, if one is configured for autonegotiation while the other one has a fixed mode of operation that is full duplex (no autonegotiation). In such conditions, the autonegotiation device correctly detects the speed of operation, but is unable to correctly detect the duplex mode.
As a result, it sets the correct speed but assumes half-duplex mode.
When a device is operating in full duplex while the other one operates in half duplex, the connection works reliably only at a very low throughput." Reference: https://en.wikipedia.org/wiki/Autonegotiation#Duplex_mismatch
NEW QUESTION # 710
Drag and drop the DHCP snooping terms from the left onto the descriptions on the right.
Answer:
Explanation:
Explanation
NEW QUESTION # 711
Refer to the exhibit.
What is the result if Gig1/11 receives an STP BPDU?
- A. The port goes into error-disable state
- B. The port transitions to STP blocking
- C. The port immediately transitions to STP forwarding.
- D. The port transitions to the root port
Answer: A
NEW QUESTION # 712
What is a characteristic of a Layer 2 switch?
- A. Avoids MAC address storage for faster transmission
- B. Uses routers to create collision domains
- C. Responsible for sending data in a particular sequence
- D. Uses the data link layer for communications
Answer: D
NEW QUESTION # 713
Refer to the exhibit. R1 has just received a packet from host A that is destined to host B.
Which route in the routing table is used by R1 to reach host B?
- A. 10.10.13.0/25 [108/0] via 10.10.10.10
- B. 10.10.13.0/25 [110/2] via 10.10.10.2
- C. 10.10.13.0/25 [1/0] via 10.10.10.2
- D. 10.10.13.0/25 [110/2] via 10.10.10.6
Answer: A
Explanation:
OSFP routing, indicated by area 0 routing command, has AD of 110. There is a floating static route configured with 108 AD. As the configured static route's AD is lower (108) than the OSPF's default AD (110) it will route the traffic via 10.10.10.10 because it has the lowest AD and thus will be put into the routing table.
NEW QUESTION # 714
In QoS, which prioritization method is appropriate for interactive voice and video?
- A. round-robin scheduling
- B. expedited forwarding
- C. traffic policing
- D. low-latency queuing
Answer: D
NEW QUESTION # 715
Refer to the exhibit.
An engineer configures interface fa0/1 on SW1 and SW2 to pass traffic from two different VLANs. For security reasons, company policy requires the native VLAN to be set to a nondefault value. Which configuration meets this requirement?
- A.
- B.
- C.
- D.
Answer: C
NEW QUESTION # 716
Refer to the exhibit. The static routes were implemented on the border router. What is the next hop IP address for a ping sent to 172.16.153.154 from the border router?
- A. 10.56.22.23
- B. 10.35.47.17
- C. 10.12.13.14
- D. 10.65.34.19
Answer: A
Explanation:
Routing uses longest-prefix match. 172.16.153.154 matches 172.16.0.0/16 (more specific than
172.0.0.0/8), and it does not match the /32 host route (which is only for 172.16.153.153).
Therefore the next hop is 10.56.22.23.
NEW QUESTION # 717
Refer to the exhibit.
A packet is being sent across router R1 to host 172.16.0.14. What is the destination route for the packet?
- A. 209.165.200.250 via Serial0/0/0
- B. 209.165.200.254 via Serial0/0/0
- C. 209.165.200.246 via Serial0/1/0
- D. 209.165.200.254 via Serial0/0/1
Answer: D
NEW QUESTION # 718
Refer to the exhibit.
Which command provides this output?
- A. show ip route
- B. show ip interface
- C. show interface
- D. show cdp neighbor
Answer: D
NEW QUESTION # 719
What is the purpose of an SSID?
- A. It identities an individual access point on a WLAN
- B. It provides network security
- C. It differentiates traffic entering access posits
- D. It identifies a WLAN
Answer: A
NEW QUESTION # 720
Drag and Drop Question
Drag and drop the IPv6 address type characteristics from the left to the right.
Answer:
Explanation:
Explanation:
https://www.ciscopress.com/articles/article.asp?p=2803866&seqNum=4
NEW QUESTION # 721
What are two differences between optical-fiber cabling and copper cabling? (Choose two.)
- A. Light is transmitted through the core of the fiber
- B. The data can pass through the cladding
- C. A BNC connector is used for fiber connections
- D. The glass core component is encased in a cladding
- E. Fiber connects to physical interfaces using RJ-45 connections
Answer: A,D
Explanation:
Section: Network Fundamentals
NEW QUESTION # 722
Refer to the exhibit.
A network administrator assumes a task to complete the connectivity between PC A and the File Server.
Switch A and Switch B have been partially configured with VLAN 10, 11, 12, and 13. What is the next step in the configuration?
- A. Add PC A to the same subnet as the Fie Server allowing for intra-VLAN communication.
- B. Add VLAN 13 to the trunk links on Switch A and Switch B for VLAN propagation
- C. Add a router on a stick between Switch A and Switch B allowing for Inter-VLAN routing.
- D. Add PC A to VLAN 10 and the File Server to VLAN 11 fa VLAN segmentation
Answer: B
NEW QUESTION # 723
......
Cisco 200-301: Cisco Certified Network Associate is a certification exam designed to test the skills and knowledge of network engineers and technicians. 200-301 exam is the replacement for the previous CCNA certification exams and covers a wide range of topics related to networking. The CCNA certification is one of the most sought-after certifications in the IT industry, and passing 200-301 exam can open up a world of opportunities for professionals.
200-301 Exam Dumps Pass with Updated 2026 Certified Exam Questions: https://gocertify.actual4labs.com/Cisco/200-301-actual-exam-dumps.html